No you can't, but I have an air bag system that will. For your 1996 Ford F-250 with an in bed hitch, I recommend the Air Lift LoadLifter 5000 Air Helper Springs item # AL57298. This system is compatible with your B&W hitch and has a 5,000 lbs load leveling capacity. This kit does require drilling but it and item # AL88298 are the only options available for your truck that are compatible with in bed hitches and they both involve drilling.
The Firestone Ride-Rite Air Helper Springs item... view full answer...
The winch itself has a 1500 lb capacity, or 750 lbs per cable. If you click the provided link, you can see a helpful FAQ article and a product demonstration video for the # DL10965 winch. view full answer...
The seal that is part of the mechanism in Repair Kit # RP320 has a 1.53 inch outer diameter. It can't be easily removed from the mechanism though. I have included a picture with other measurements for other parts in this kit as well. view full answer...
I spoke with my contact at Curt regarding front mount trailer hitch, # 31026. He stated that the distance from outside plate to outside plate is 40.6 inches. The distance across between bolt holes is 36-3/4 inches on center. I have included a link to the installation details for this hitch for reference. view full answer...
Yes, it will! The B&W Universal Base Rails and Installation Kit for 5th Wheel Trailer Hitches item # BWRVR3200 includes industry standard 5th wheel rails that are compatible with the Reese 30032 5th wheel hitch. The Reese 30032 uses the same industry standard mounting pattern.
I have attached a diagram below with the dimensions for the mounting holes that shows exactly which slots Reese hitches use.
The B&W Universal Base Rails and Installation Kit for 5th Wheel Trailer Hitches item... view full answer...
The weight capacity of the Bulletproof Hitches Shackle Hitch part # ED20SHACKLE is the working load limit. So it would be totally fine to use with up to a 30,000 lb load. view full answer...
Curt trailer hitch # C15316 is a custom fit hitch designed to 1999 - 2003 Ford F-250 and F-350 Super Duty Pickups with factory Deep Drop Bumpers, sometimes called a cowboy bumper. The hitch mounting holes are spaced approximately 34-1/2 inches apart on center. It doesn't fit a minimum or maximum frame width being a custom hitch and all.
From the mounting surface (bottom of truck frame) down to the top of the receiver is 9 inches. view full answer...
The rubber spring for the Timbren Front Suspension Enhancement System # TFF2504A that fits your 1995 Ford F-250 4x4 sits 3-3/4" tall and then all the different edges of the bracket measure 1/4". This means that from the bottom of the spring to the top of the uppermost horizontal plate measures 4-1/4". view full answer...
The distance from the top of the mounting flange to the top of the receiver tube on the B&W Heavy-Duty Trailer Hitch Receiver part # BWHDRH25198 is around 7-3/8". The distance from the top of the mounting flange to the top of the receiver tube on the Curt 3-Piece Trailer Hitch Receiver part # C15511 is around 8".
I have attached a photo of each measurement for you as well. view full answer...
The Dexter Trailer Hub and Drum Assembly # 8-201-5 has a diameter of 12 inches. It's designed for 5,200 pound axles and has a 6 on 5-1/2 bolt pattern. It will fit inner beaing # 25580 and outer bearing # LM67048. view full answer...
I checked with Buyers but they did not have this information on the Buyers Products Conduit Carrier Kit - 6" Diameter part # 337CC600. So, I went out to our warehouse for you and measured it. There is going to be about 3" of threading left once the u-bolt goes over the pipe and through the clamp. view full answer...
When installing a fifth wheel hitch like part # RP30928 on your 1995 Ford F-250, you will need to install base rails like part # RP30035.
The measurement for installing the # RP30035 base rails on your F-250 is 32-1/2 inches from the rear edge of your truck bed to the rear edge of the base rail. I have attached the installation instructions for the base rails you can check out. view full answer...
According to DeeZee, the weight capacity of the # CARR102521 Hoop Steps for your 1995 Ford F250 4x4 is 500 lbs. They'll be able to put up with whatever you can dish out. view full answer...
What you are looking for is called wheel to wheel tube steps. All of the steps for your 1994 Ford F-250 Super Cab are cab length only. They will not extend the distance between the wheels. I am not certain the length of the cab on the Super Cab models but that is how long the bars will be. They do have a single pad per bar.
If your truck is not a Heavy Duty model, you could use bed step # AS-550. This would work exactly as you need it to. And it can fold back in when not in use. It will... view full answer...
I spoke with a Buyers Products representative about the Fender Guard Mud Flaps - Black ThermoFlex - 10" Wide x 20" Tall - Qty 2, part # 337B1020PPB. They emailed me a dimensional drawing of one of these mud flaps. They matched the ones you attached to your question. I measured them myself to triple check and the correct dimensions are the ones you received from Buyers Products. view full answer...
The trailer hitch (Curt, Draw-Tite, B&W) for a 1996 Ford F-250/F-350 that fits closest to the bottom of the bumper is the B&W Heavy-Duty Trailer Hitch Receiver part # BWHDRH25122 which measures 5" from the top of the flange to the top of the receiver tube. The Curt part # C15300 measures 5-1/2" and the Draw-Tite part # DT45502 5-1/4". view full answer...
After speaking to my contact at Brophy, she informed me the Brophy Camper Hold Down # HSSF technically does not have a weight range. This product is limited only by the weight capacity of your 1995 Ford F-250, so you will need to consult your vehicle owners guide to find the weight limit of your cargo bed.
You will also need to ensure there is at least 2 inches of space between the truck bed interior wall and the lip of the bed in order for the hold downs to fit properly. I have included... view full answer...
The cushioned ball mount # AMSC2HD is given its rating based on extensive testing and the design of the components. That does include the cushions on the inside of the shank. So in other words if they tested it at 14K and the cushions failed they would not rate it for 14K. The ball mount meets Society of Automotive Engineers J684 specs. The cushion is going to provide more and more resistance the further or harder it is pushed against so it would not collapse or anything like that. view full answer...
The first thing you are going to want to do is measure the width of the frame on your 1996 Ford F-250 to determine the width of the frame. Measure from the outside on one side to the outside on the other side. Trailer hitch # C15300 is made for trucks with a frame width of 37-1/4 inches.
I have included a picture that shows the measurements between all the holes on the hitch, center to center.
I also recommend the etrailer ball mount kit # EBMK2416. It comes with a ball mount, 2 balls,... view full answer...